分类
标准

DIN EN 12697-16-2004 沥青混合物 热混合沥青的检验 第16部分:尖铁轮胎磨损

《沥青混合物 热混合沥青的检验 第16部分:尖铁轮胎磨损》的编号是DIN EN 12697-16-2004,目前的状态为作废,该标准分类为石油,石油产品。

标准编号:DIN EN 12697-16-2004

状态:作废

强制性标准:

开本页数:19

采用关系:DIN EN 12697-16-2004

中图分类号:E3

中国标准分类号:E;E43

国际标准分类号:93;93.080.20

《沥青混合物 热混合沥青的检验 第16部分:尖铁轮胎磨损》是石油,石油产品分类下的标准,This Standard describes two alternative procedures (method A and method B) for preparing and determination of abrasion caused by studded tyres, tested on cylindrical specimens of bituminous mixtures. Note 1: Both methods (A and B) may be used where relevant for determination of abrasion by studded tyres. Note 2: Method A originates from the Prall-method, but it is improved by comprehensive research work to meet an adequate design. According to Swedish research work the method correlates with abrasion in the field. Method B originates from Finnish experience and correlates with abrasion in the field.其主要内容是16,尖铁,沥青,磨损。

以上就是关于沥青混合物 热混合沥青的检验 第16部分:尖铁轮胎磨损的介绍。

分类
标准

BS EN 12594-2000(R2004) 石油及其产品的试验方法沥青和沥青粘合剂 试样的制备

《石油及其产品的试验方法沥青和沥青粘合剂 试样的制备》的编号是BS EN 12594-2000(R2004),目前的状态为废止,实施日期是2000-07-15,该标准分类为石油,石油产品。

标准编号:BS EN 12594-2000(R2004)

状态:废止

强制性标准:

实施日期:2000-07-15

开本页数:10

采用关系:BS EN 12594-2000(R2004)

中图分类号:E3

中国标准分类号:E;E43

国际标准分类号:91;91.100.50

《石油及其产品的试验方法沥青和沥青粘合剂 试样的制备》是石油,石油产品分类下的标准,其主要内容是试样,制备,沥青,粘合剂。

以上就是关于石油及其产品的试验方法沥青和沥青粘合剂 试样的制备的介绍。

分类
标准

ASTM D4867/D4867M-2009 水分对沥青混凝土铺路混合物影响的试验方法

《水分对沥青混凝土铺路混合物影响的试验方法》的编号是ASTM D4867/D4867M-2009,目前的状态为现行,实施日期是2009-07-01,该标准分类为石油,石油产品。

标准编号:ASTM D4867/D4867M-2009

状态:现行

强制性标准:

实施日期:2009-07-01

开本页数:5

采用关系:ASTM D4867/D4867M-2009

中图分类号:E3

中国标准分类号:E;E43

国际标准分类号:93;93.080.20

《水分对沥青混凝土铺路混合物影响的试验方法》是石油,石油产品分类下的标准,This test method can be used to test asphalt concrete mixtures in conjunction with mixture design testing to determine the potential for moisture damage, to determine whether or not an antistripping additive is effective, and to determine what dosage of an additive is needed to maximize the effectiveness. This test method can also be used to test mixtures produced in plants to determine the effectiveness of additives under the conditions imposed in the field.1.1 This test method covers procedures for preparing and testing asphalt concrete specimens for the purpose of measuring the effect of water on the tensile strength of the paving mixture. This test method is applicable to dense mixtures such as those appearing in the Table for Composition of Bituminous Paving Mixtures in Specification D 3515. This test method can be used to evaluate the effect of moisture with or without antistripping additives including liquids and pulverulent solids such as hydrated lime or portland cement. 1.2 The values stated in either SI units or inch-pound units in parentheses shall be regarded separately as standard. The values in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining values in any way. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.其主要内容是混合物,铺路,混凝土,沥青。

以上就是关于水分对沥青混凝土铺路混合物影响的试验方法的介绍。

分类
标准

ASTM D7369-2009 用间接拉伸测试法测定沥青混合料弹性模数的试验方法

《用间接拉伸测试法测定沥青混合料弹性模数的试验方法》的编号是ASTM D7369-2009,目前的状态为废止,实施日期是2009-02-01,该标准分类为石油,石油产品。

标准编号:ASTM D7369-2009

状态:废止

强制性标准:

实施日期:2009-02-01

开本页数:12

采用关系:ASTM D7369-2009

中图分类号:E3

中国标准分类号:E;E43

国际标准分类号:75;75.140

《用间接拉伸测试法测定沥青混合料弹性模数的试验方法》是石油,石油产品分类下的标准,Resilient modulus can be used in the evaluation of materials quality and as input for pavement design, evaluation and analysis. With this method, the effects of temperature and load on resilient modulus can also be investigated. Note 18212;The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Practice D 3666 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with D 3666 alone does not completely assure reliable results. Reliable results depend on many factors; following the suggestions of D 3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.1.1 This test method covers procedures for preparing and testing laboratory-fabricated or field-recovered cores of bituminous mixtures to determine resilient modulus values using a repeated-load indirect tension test. 1.2 The values stated in SI units are regarded as the standard. Values in parentheses are for informational use. 1.3 A precision and bias statement for this standard has not been developed at this time. Therefore, this standard should not be used for acceptance or rejection of a material for purchasing purposes. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.其主要内容是拉伸,沥青,模数,法测定。

以上就是关于用间接拉伸测试法测定沥青混合料弹性模数的试验方法的介绍。

分类
标准

ASTM D3289-2008 用镍钳埚测定半固态及固态沥青材料密度的试验方法

《用镍钳埚测定半固态及固态沥青材料密度的试验方法》的编号是ASTM D3289-2008,目前的状态为现行,实施日期是2008-01-01,该标准分类为石油,石油产品。

标准编号:ASTM D3289-2008

状态:现行

强制性标准:

实施日期:2008-01-01

开本页数:3

采用关系:ASTM D3289-2008

中图分类号:E3

中国标准分类号:E;E43

国际标准分类号:93;93.080.20

《用镍钳埚测定半固态及固态沥青材料密度的试验方法》是石油,石油产品分类下的标准,Values of density are used for converting volumes to units of mass, and for correcting measured volumes from the temperature of measurement to a standard temperature using Practice D 4311.1.1 This test method covers the determination of the density of semi-solid and solid bituminous materials by weighing in air and in water. Note 18212;An alternate method for determining the density of semi-solid and solid bituminous materials is Test Method D 70. For materials which are too fluid for use of this method, use Test Method D 3142. 1.2 The values stated in SI units are to the regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.其主要内容是固态,钳埚,沥青,测定。

以上就是关于用镍钳埚测定半固态及固态沥青材料密度的试验方法的介绍。

分类
标准

NF T66-024-2002 乳化沥青 与水泥混合的稳定性试验

《乳化沥青 与水泥混合的稳定性试验》的编号是NF T66-024-2002,目前的状态为废止,该标准分类为石油,石油产品。

标准编号:NF T66-024-2002

状态:废止

强制性标准:

开本页数:8

采用关系:NF T66-024-2002

中图分类号:E3

中国标准分类号:E;E43

国际标准分类号:75;75.140

《乳化沥青 与水泥混合的稳定性试验》是石油,石油产品分类下的标准,其主要内容是水泥,乳化,沥青,稳定性。

以上就是关于乳化沥青 与水泥混合的稳定性试验的介绍。

分类
标准

NF T66-021-1999 乳化沥青 乳化沥青缩粒电荷符号的测定

《乳化沥青 乳化沥青缩粒电荷符号的测定》的编号是NF T66-021-1999,目前的状态为废止,该标准分类为石油,石油产品。

标准编号:NF T66-021-1999

状态:废止

强制性标准:

开本页数:12

采用关系:NF T66-021-1999

中图分类号:E3

中国标准分类号:E;E43

国际标准分类号:75;75.140

《乳化沥青 乳化沥青缩粒电荷符号的测定》是石油,石油产品分类下的标准,其主要内容是电荷,乳化,沥青,缩粒。

以上就是关于乳化沥青 乳化沥青缩粒电荷符号的测定的介绍。

分类
标准

ASTM D139-1995(2001)e1 沥青材料的浮选试验方法

《沥青材料的浮选试验方法》的编号是ASTM D139-1995(2001)e1,目前的状态为废止,该标准分类为石油,石油产品。

标准编号:ASTM D139-1995(2001)e1

状态:废止

强制性标准:

开本页数:3

采用关系:ASTM D139-1995(2001)e1

中图分类号:E3

中国标准分类号:E;E43

国际标准分类号:93;93.080.20

《沥青材料的浮选试验方法》是石油,石油产品分类下的标准,其主要内容是材料,试验,沥青,浮选。

以上就是关于沥青材料的浮选试验方法的介绍。

分类
标准

ASTM D6648-2008 用挠曲梁流变仪测定沥青结合料弯曲蠕变强度的试验方法

《用挠曲梁流变仪测定沥青结合料弯曲蠕变强度的试验方法》的编号是ASTM D6648-2008,目前的状态为现行,实施日期是2008-01-15,该标准分类为石油,石油产品。

标准编号:ASTM D6648-2008

状态:现行

强制性标准:

实施日期:2008-01-15

开本页数:14

采用关系:ASTM D6648-2008

中图分类号:E3

中国标准分类号:E;E43

国际标准分类号:93;93.080.20

《用挠曲梁流变仪测定沥青结合料弯曲蠕变强度的试验方法》是石油,石油产品分类下的标准,The temperatures for this test are based upon the winter temperature experienced by the pavement in the geographical area for which the asphalt binder is intended. The flexural creep stiffness or flexural creep compliance, determined from this test, describes the low-temperature stress-strain-time response of asphalt binder at the test temperature within the range of linear viscoelastic response. The low-temperature thermal cracking performance of asphalt pavements is related to the creep stiffness and the m-value of the asphalt binder contained in the mix. The creep stiffness and the m-value are used as performance-based specification criteria for asphalt binders in accordance with Specification D 6373. 1.1 This test method covers the determination of the flexural-creep stiffness or compliance and m-value of asphalt binders by means of a bending beam rheometer. It is applicable to material having flexural-creep stiffness values in the range of 20 MPa to 1 GPa (creep compliance values in the range of 50 nPax2013;1 to 1 nPax2013;1) and can be used with unaged material or with materials aged using aging procedures such as Test Method D 2872 or Practice D 6521. The test apparatus may be operated within the temperature range from x2013;36x00B0;C to 0x00B0;C. 1.2 Test results are not valid for test specimens that deflect more than 4 mm or less than 0.08 mm when tested in accordance with this test method. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.其主要内容是蠕变,挠曲,沥青,流变。

以上就是关于用挠曲梁流变仪测定沥青结合料弯曲蠕变强度的试验方法的介绍。

分类
标准

KS M5960-1999 沥青用清漆

《沥青用清漆》的编号是KS M5960-1999,目前的状态为现行,该标准分类为石油,石油产品。

标准编号:KS M5960-1999

状态:现行

强制性标准:

开本页数:3

采用关系:KS M5960-1999

中图分类号:E3

中国标准分类号:E;E45

国际标准分类号:75;75.140

《沥青用清漆》是石油,石油产品分类下的标准,其主要内容是清漆,沥青。

以上就是关于沥青用清漆的介绍。